Wednesday, August 12, 2020

BSNL FTTH not working

 BSNL FTTH Problems & troubleshooting

BSNL ftth is growing day by day in the telecom industry as it is best in the market. People face difficulty when FTTH not working. So here I am describing some basic problems of the BSNL ftth and their solutions. 

Possible cause for FTTH not working 
1. First reason may be that the fiber connectivity may be broken.

2. Other possible cause may be the configuration issue of the ONT.
 
3. Check also your network settings as specified by the BSNL at the time of installation, may be your network settings have been changed by someone else. 

4. One reason may also be there that the media connectivity from the far end that is the exchange end is broken in-between customer modem and the gateway. 

5. Sometimes the problem may be with the particular site your check regularly and other sites are working. You may check for other websites.
 
6. Last reason may be you have not paid bill of the service and BSNL has disconnected the service. So check for the payment. 


PON lamp indication

PON light red or no light on it, there are two possible case of it. Either the fiber is break somewhere or the power coming in the fiber is Low or high than the threshold. 

PON light  blinking, then the possible cause can be configuration issue of the ONT or OLT. 
If PON led is green stable then FTTH is in working condition.

FTTH speed problems
If you are facing speed issue in the BSNL FTTH then do the following steps to check
  • Check for DNS settings it should be  primary DNS 61.1.1.1 and 61.0.3.3
  • MTU size is necessary step to check it should be between 1400-1500. The best possible value for the MTU size for BSNL FTTH is 1460.
  • Fiber power for better speed is between -14 dB to -25 dB. You cannot check the fiber power directly you should get it checked by the engineer that visit your area in case of failure

Note: sometimes just restarting your modem can resolve the problem for you

Data light is not showing

If your data light is not glowing then the problem may be in the configuration of the modem. Then you will need to configure your ftth modem. 

NETLINK Modem configuration

1. Login ip for netlink modem is 192.168.1.1

username: admin
password: stdONU101

Service type : softswitch SIP
SIP register address: 10.187.6.12
Subscribe: Enabled
Outbound Proxy : Enabled
Outbound proxy address: 10.187.6.12
SIP DOMAIN: 10.187.6.12


BSNL FTTH complain

You can book bsnl ftth complain on the bsnl selfcare portal. Click on the register complaint option shown on the left side. Select bharatfiber voice and broadband. Enter your telephone number alotted and select complain type. click on submit complain and your complain is registered. 

In short if your BSNL FTTH is not working first of all raise online complain using the bsnl selfcare portal. Then do check my suggestions. Even if the problem is not solved wait for the engineer after raising the complain. 

And if you found any other issue, let me know by mentioning your problem in the comment section. 

Thanks for reading









Sunday, August 2, 2020

e-pass uttarakhand online apply

e-pass for lockdown in uttarakhand


People are asking in social media for how to apply for e-pass in uttarakhand online. It is necessary to apply for e-pass for movement outside the state and for movement inside the state from other place. You will have to undergo mandatory 14 days home quarantine after the movement. 

There are two options available on the official website.
1. e-pass application for travelling from uttarakhand 
2. e-pass application for travelling to uttarakhand

Step by step guide to apply for e-pass in uttarakhand online

1.   Visit the official website www.dsclservices.org.in

2. Click on e-pass प्रवासी और अन्य पंजीकरण  It will open the following form shown below


3. Read all general instructions shown on the page. 

4. Fill all the details carefully like mode of travel, pass category, journey date and so on. 

5. You will have to provide mobile number on which you will receive OTP after the form has been filled by you. 

6. You will have to upload documentary address proof. You can upload any document like aadhar, voter id, pan card. 

7. Enter the OTP received on your contact number. 

8. After entering the OTP click on submit button and your application will be submitted with an application number. Note down the application number shown as it will be required to check the status of the e-pass applied. 

Terms and conditions:

1. The applicant will have to undergo 14 days mandatory quarantine.
2. The applicant should not be from any containment zone.
3. On entering the state you will need to submit medical certificate. 

e-pass uttarakhand online status

To check the status of the e-pass visit the same official site www.dsclservices.org.in . Enter the application number provided at the time of submission of e-pass application. It will show you the status of your online e-pass application. If e-pass is approved by the government of uttarakhand, click on download e-pass. 

If you find this helpful and informative, subscribe my page.
If you are having any problem in applying e-pass online comment me.